The idea of publishing ROSEN
In the 2016 report, the authors attributed the increase in magnetic density to a more detailed representation of complex corrosion. Discussions are ongoing on the retention of sensors in the trajectory, normalization of channels and automation of large array of signals. The name with the laser scan describes a desire for detailed representation, but does not make the magnetic method a direct optical measurement of the surface.
For engineering reading, it is important to separate three results: register more counts, restore the form of metal loss and use this form in calculation. They are between calibration, interpretation model and uncertainty assessment.
How a magnetic image is formed
The MFL sensor shall record the scattering field under magnetization conditions. The signal is influenced by the size and orientation of the non-fault, the magnetic properties of the metal, the gap and the position of the sensor. So color-diversion is a map of measured or transformed signal, not a photograph of the bottom of corrosive ulcer.
A model of signal-geometric communication is required to obtain the defect dimensions. The grid provides models with more spatial information, but does not eliminate the ambiguity of the return. Two near signals can occur at different combinations of depth, length and shape.
The permit starts with mechanics.
The nominal step of the sensors is only useful when their real trajectory is known. The removal of the unit through welding, support leg wear or lever swings can create local pass or cover tracks. The programmatic increase in the image does not compensate for the physically missing measurement.
The design of the sensitive block should therefore be considered together with the surface map. We need to estimate the clamping, permit movement, stability and recording of signs of loss of contact. For the inspection tool designer, this is a direct link between mechanical tolerance and the quality of the output data: a convenient layout does not always provide the necessary spatial stability.
Normalization without destroying the useful signal
The nearby channels may have different sensitivity and are in a different magnetic field. If you don't take these differences into account, the stripes that are similar to those of a pipe appear on the unwrapped. If you adjust too aggressively, you can suppress a long real anomaly.
The operating algorithm shall maintain the baseline and transformation parameters. Then an analyst can check whether a feature existed before or after processing. The control areas and the comparison of behaviour between several field components are particularly useful. Normalization should eliminate hardware heterogeneity, while maintaining physical substantive differences between neighbouring points and pipeline sections.
Separate ulcer and damage group
The more detailed map sometimes divides the area that rough grid represented as a single defect into several local deluges. But the decision about their interaction cannot be made solely by whether or not the colour spots are divided. Harmonized grouping rules and metal junctions are required.
The shape along the pipe, the maximum depth and the mutual position of the sections are important for a solid assessment. The refinement of topography can reduce both excessive conservativeness and reveal a previously hidden deep area. Therefore, the increase in the permit should not be automatically described as a way to reduce repairs: the direction of change of decision depends on the geometry found.
Verification of independent measurements
Comparison with laser scanner is useful only when the coordinates are closely combined and the surface condition is understood. Cleaning, metal access and selection of the support surface intact affect the result of ground measurements. The scan itself also has errors and omissions.
Correct check compares the same physical values. You can't compare the maximum depth of one small ulcer with the average depth of a large magnetic map window. Interpolation rules, cell size, mask of missing data and method of defining the nominal wall should be retained. Otherwise, the improvement of the image is easily taken as an improvement in metrology.
Big data requires managed processing
The growth in the number of channels increases the pressure on memory, food, transmission and software testing. For on-board electronics, the capacity of the entire tract is important, including recording at maximum speed. The reproducibility of the algorithm version is important to an analyst.
Automatic classification helps to select candidates for analysis, but its quality is assessed by independent data and specific types of anomalies. The overall response rate is not very good at referring to rare deep ulcers. It is useful to take separately into account omissions, false reactions and cases where the algorithm should pass a decision on to an expert because of lack of confidence.
Conclusion for the development of OKB
Detailed magnetic diagnostics are the common task of mechanics, sensors, electronics and software. The step requirements should be translated into sensor trajectory, frequency of recording, accuracy of coordinates and preservation of the input data.
To present the results, we believe it is important to separate the measured signal from the re-established geometry and the state estimation. This approach allows for substantive discussion of quality. The historical development of ROSEN shows the relationship between the density of measurement and the quality of interpretation. In practice, it is useful to show a set of original magnetic detachment, a re-established depth and a map of uncertainty: this remains the local detailing of the result related to the physical base.
Engineering output
The grid is useful when it is supported by a surface, sensor stability and size restoration accuracy.
Sources and further reading
- PPSA Technical Report 2016; open PDFFrank Flatau, Michael Rapp, ROSEN — MFL Results Like a Laser Scan ↗
The article was originally written in Russian. It summarises the cited sources. For the original text and illustrations, consult the publications listed below.